/* Imported from Wayback Machine
   Original URL : https://www.retrobrewcomputers.org/doku.php?id=builderpages:plasmo:k80:k80w_r1
   Snapshot date: 2025-05-16
   Generator    : wayback-archiver
*/

====== K80W Rev1, A RomWBW-capable Z80 SBC ======

===== Introduction =====

**Note, K80W rev1 is superceded by [[builderpages:plasmo:k80:k80w_r21|K80W rev2.1]]**

K80W is similar to K80. It is a 22MHz Z80 SBC with KIO (Z84C90) as the I/O device. It is designed to run RomWBW

[[https://www.retrobrewcomputers.org/lib/exe/fetch.php?tok=28cfe8&media=https://www.retrobrewcomputers.org/lib/plugins/ckgedit/fckeditor/userfiles/image/builderpages/plasmo/k80/k80w_rev1_annotated.jpg|{{https://www.retrobrewcomputers.org/lib/plugins/ckgedit/fckeditor/userfiles/image/builderpages/plasmo/k80/k80w_rev1_annotated.jpg?600x470|www.retrobrewcomputers.org_lib_plugins_ckgedit_fckeditor_userfiles_image_builderpages_plasmo_k80_k80w_rev1_annotated.jpg}}]]

===== Features =====

Z80 overclocked to 22MHz,

512KB Flash divided into 16 32KB banks,

512KB RAM divided into 16 32KB banks,

KIO, Z84C90, is the integrated I/O interface,

DS1302 Real Time Clock,

Compact Flash interface,

Designed for RomWBW

Two 40-pin RC2014-compatible expansion slots,

100mm X 100mm, 2-layer PC board,

===== Design Files =====

[[https://www.retrobrewcomputers.org/lib/exe/fetch.php?media=builderpages:plasmo:k80:k80w_rev1_scm.pdf|Schematic]]

[[https://www.retrobrewcomputers.org/lib/exe/fetch.php?media=builderpages:plasmo:k80:k80w_rev1_gerber.zip|Gerber photoplots]]

[[https://www.retrobrewcomputers.org/lib/exe/fetch.php?media=builderpages:plasmo:k80:k80rev1:k80w_r1pcb_cpld_epm7032s.zip|CPLD design files]]

Bill of Materials

==== Software ====

==== Adding SD to K80W ====

[[https://www.retrobrewcomputers.org/lib/exe/fetch.php?tok=3aa667&media=https://www.retrobrewcomputers.org/lib/plugins/ckgedit/fckeditor/userfiles/image/builderpages/plasmo/k80/k80wwithsd.jpg|{{https://www.retrobrewcomputers.org/lib/plugins/ckgedit/fckeditor/userfiles/image/builderpages/plasmo/k80/k80wwithsd.jpg?400x383|www.retrobrewcomputers.org_lib_plugins_ckgedit_fckeditor_userfiles_image_builderpages_plasmo_k80_k80wwithsd.jpg}}]]

PB0 to MOSI,

PB7 to MISO,

PB3 to CS and

PB4 to CLK

=== RomWBW Configuration ===

The following modifications to RCZ80_K80W.ASM file is needed:

SDENABLE .SET TRUE ; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)\\
SDMODE .SET SDMODE_PIO ; SD: DRIVER MODE: SDMODE_[JUHA|N8|CSIO|PPI|UART|DSD|MK4|SC|MT|PIO|Z80R|USR]

\\
This is the resulting [[https://www.retrobrewcomputers.org/lib/exe/fetch.php?media=builderpages:plasmo:k80:k80rev1:rcz80_k80w.asm|RCZ80_K80W.ASM]]

The I/O addresses for SDMODE_PIO is hardwired to $69. It is necessary to modify SD.ASM in HBIOS as follow:

SD_IOBASE .EQU $82 ; IO BASE ADDRESS FOR SD INTERFACE

SD_DDR .EQU $83 ; DATA DIRECTION REGISTER

This is the resulting [[https://www.retrobrewcomputers.org/lib/exe/fetch.php?media=builderpages:plasmo:k80:k80rev1:rcz80_k80w_rom_sd.zip|ROM binary file]] that recognizes SD card connected to PIO: