| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| builderpages:speed3ple:start [2025/01/15 01:37] – Revision from 2025-01-15 | builderpages:speed3ple:start [2026/06/15 13:22] (current) – external edit 127.0.0.1 |
|---|
| | /* Imported from Wayback Machine |
| | Original URL : https://retrobrewcomputers.org/doku.php?id=builderpages:speed3ple:start |
| | Snapshot date: 2023-10-02 |
| | Generator : wayback-archiver |
| | */ |
| | |
| | ====== Project page for speed3ple: ====== |
| | |
| | Mostly Z80 ECB stuff here… |
| | |
| | ^System/Board ^Status ^Comments ^ |
| | |[[builderpages:speed3ple:ecb-backplane4|ECB-backplane-4]] |2 x working |Nice little test bench | |
| | |[[builderpages:speed3ple:ecb-backplane8|ECB-backplane-8]] |1 x working |This is the backplane I use the most, has a LPS42 power inside. Plan to build one more. | |
| | |[[builderpages:speed3ple:ecb-bp-12|ECB-backplane-12]] |1 x working |I got a Siemens 505-6508 PLC case for this. Still trying to figure out a power and wire placement in that case. | |
| | | | | | |
| | |ECB-SBC-v2-3a |3 x working |Solid board, no trouble at 4, 8 and 10Mhz. 1 built with vintage 7400 TTL at 8Mhz. | |
| | |[[builderpages:speed3ple:ecb-sbc-v2-004z|ECB-SBC-v2-4z]] |2 x working |Works fine at 10Mhz w/TTL+CMOS Z80. Got sound, speed switch works, recovery mode switch not tested yet. | |
| | |[[builderpages:speed3ple:ecb-sbc-v5i|ECB-SBC-v5i]] |1 x working |Seems to be working and stable at 10Mhz with LS logic and RomWBW v3.0.1. I'm testing this now. Looks great! | |
| | |[[builderpages:speed3ple:ecb-z180mk4|ECB-Z180 mk4]] |2 x working |Solid board, no trouble. Works good at (1:1)18.432Mhz with pure LS logic. Got 3 fake Z180 cpu first… | |
| | |[[builderpages:speed3ple:ecb-kiss-68030|ECB-KISS-68030]] |1 x under construction|Still not working! maybe I got some bad parts? | |
| | |[[builderpages:speed3ple:ecb-mf-pic|ECB-MF-PIC]] |2 x under construction|Completed but un-tested | |
| | |[[builderpages:speed3ple:diskiov3|ECB-DiskIO v3]] |4 x working |Angled IDE connector for easy topside CF card access | |
| | |[[builderpages:speed3ple:ecb-dualsd|ECB-DualSD]] |1 x working |Works fine with SBC v4z (12Mhz). PCB made from the new Gerber files (Thanks!).\\ Compile RomWBW with SDENABLE.SET TRUE and SDMODE.SET SDMODE_DSD\\ The SD card sockets I have (ebay) needed bending of WP pin.| |
| | |[[builderpages:speed3ple:ecb-ramfloppy|ECB-RamFloppy]] |2 x working |R11 version. Built with 8 x xAS6C4008. I used a TLC7705D SMD version. Good read/write speeds! | |
| | |[[builderpages:speed3ple:ecb-cassetteif|ECB-Cassette IF]] |2 x working |Built both version, 300+600 baud. Value of timing capacitor C2 is critical. | |
| | |[[builderpages:speed3ple:ecb-vdu|ECB-VDU]] |1 x under construction|Does not work yet. Maybe got some bad parts? | |
| | |[[builderpages:speed3ple:ecb-vga3|ECB-VGA3]] |1 x under construction|Does not work yet. Maybe got some bad parts? | |
| | |[[builderpages:speed3ple:ecb-propio-v2|ECB-PropIO v2]] |3 x working |Runs firmware from RomWBW v2.9.1(v0.95). | |
| | |[[builderpages:speed3ple:ecb-zilog-p|ECB Zilog Peripheral]] |1 x under testing |PCB v2, with 1xDART, 2xPIO and CTC. | |
| | |[[builderpages:speed3ple:ecb-4pio-r04|ECB-4PIO-R04]] |1 x working |I got it working, will make a new cable and test more. | |
| | |[[builderpages:speed3ple:dsky|DSKY]] |1 x working |Completed and is working | |
| | |[[builderpages:speed3ple:ecb-ecb-bus-monitor|ECB-Bus Monitor]]|1 x under test |Blinkenlights blinks, but I don't fully understand how to use this… | |
| | |[[builderpages:speed3ple:ecb-usb-fifo|ECB-USB-FiFo]] |1 x under test | | |
| | |[[builderpages:speed3ple:ecb-prototype-iii|ECB-Prototype-III]]|3 x under construction| | |
| | |[[builderpages:speed3ple:ecb-atb|ECB-ATB]] |1 x under test |Got this working, i think, but… | |
| | |ECB-SCG |1 x under construction|Status: have PCB, collecting parts… | |
| | |ECB-VGM |1 x under construction|Status: have PCB, collecting parts… | |
| | | | | | |
| | |**Hardware Terminals** | | | |
| | |Geoff Graham |1 x Built, testing |Serial RS-232 to VGA/Composite hardware terminal based on Microchip PIC32MX250F128B. Single chip ASCII video display terminal with VT100 and VT52 emulation. | |
| | |uTerm-S |1 x Built, working |Serial RS232 to VGA hardware VT-100 terminal based on STM32F030F4P6 CPU. Using ChibiTerm for emulating video. Project found on hackaday / “Just4fun” | |
| | |uTerm2-S |1 x under construction|Serial RS232 to VGA hardware terminal based on ESP32-Wroom-32 module. Emulation based on FabGL library. Project found on hackaday / “Just4fun” | |
| | |VersaTerm |1 x under construction|Serial RS232 to VGA/HDMI hardware terminal based on Raspberry Pi Pico module and PicoVGA library for generating video signals. Project found on github / “dhansel” | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | |**Non-ECB systems:** | | | |
| | |[[builderpages:speed3ple:zeta2|Zeta 2]] |2 x working |Stable at 16Mhz(LS) and 20Mhz (AHCT). 1 built into a metal case together with ParPortProp as a unit | |
| | |[[builderpages:speed3ple:easy-z80|Easy-Z80]] |1 x working |Small and easy to build. I got the v1.1 pcb. Nice! Update: I connected a RC2014 IDE board for CF card storage. | |
| | |[[builderpages:speed3ple:z80-grants|Z80-GrantS]] |1 x working |Small pcb based on Grant Searle Z80. Runs basic. | |
| | |[[builderpages:speed3ple:z80-trainer|Z80-Trainer]] |1 x working |Big 4 layer board by smbaker. Has keyboard and optional TIL311s or LCD1602. Runs RomWBW. Designed w/CTC, PIO, SIO/2External RC2014 bus. | |
| | | | | | |
| | |**ISA bus boards:** | | | |
| | |ISA Micro8088 |1 x working | | |
| | |ISA backplane |1 x working | | |
| | |ISA XT-IDE |2 x under testing | | |
| | |ISA Super-VGA |1 x working | | |
| | |ISA-XT-CF-Lite |2 x working | | |
| | |ISA-FDU-Serial |1 x working | | |
| | |ISA-RTC |1 x working | | |
| | | | | | |
| | |**RC2014 boards:** | | | |
| | |RC2014-IDE |1 x under construction|IDE I/F based on 8255 chip | |
| | |RC2014-RTC |1 x under construction|Real-time clock based on 1302 chip | |
| | | | | | |
| | | | | | |
| | |
| | ^Text ^Images ^^ |
| | |\\ 2048 game in RomWBW:\\ \\ (Seems to only work with serial cable)|{{[[lib:plugins:ckgedit:fckeditor:userfiles:image:builderpages:speed3ple:images:img_20200324_190754small.jpg]] |
| | |“Hidden” Easteregg in RomWBW (Mandelbrot ascii art) |{{[[lib:plugins:ckgedit:fckeditor:userfiles:image:builderpages:speed3ple:images:img_20200324_174724small.jpg]] |
| |
