Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| boards:sbc:mini_mc14500:mini_mc14500 [2021/03/03 09:16] – Revision from 2021-03-03 | boards:sbc:mini_mc14500:mini_mc14500 [2026/06/15 12:31] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | /* Imported from Wayback Machine | ||
| + | | ||
| + | | ||
| + | | ||
| + | */ | ||
| + | |||
| + | ====== Mini MC14500 ====== | ||
| + | |||
| + | {{[[lib: | ||
| + | |||
| + | ===== Introduction ===== | ||
| + | |||
| + | The Mini MC14500 SBC is a very simple board built around the Motorola MC14500B ICU (Industrial Control Unit) https:// | ||
| + | |||
| + | All Data, Instruction and Clock entry is done via switches. | ||
| + | |||
| + | The Mini MC14500 board has the following features | ||
| + | |||
| + | 8 LED's for state output | ||
| + | |||
| + | 6 Switches for programming and data input | ||
| + | |||
| + | Expansion header to allow direct connection to say a parallel port for control by another CPU. | ||
| + | |||
| + | The silk screen for the board has all of the OP codes for quick reference | ||
| + | |||
| + | ===== Hardware Documentation ===== | ||
| + | |||
| + | Board: [[https:// | ||
| + | |||
| + | Schematic: [[https:// | ||
| + | |||
| + | KiCAD and Manufacturing Files: [[https:// | ||
| + | |||
| + | ===== Build Information ===== | ||
| + | |||
| + | BOM: [[https:// | ||
| + | |||
| + | **Test Programs** | ||
| + | |||
| + | To run the test programs you need to undertake the following as the precursor | ||
| + | |||
| + | Data: 1 | ||
| + | |||
| + | Control: IEN (1010) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | Control: OEN (1011) | ||
| + | |||
| + | //**Logical AND example**// | ||
| + | |||
| + | Data: 1 | ||
| + | |||
| + | Control: IEN (1010) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | Control: OEN (1011) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | LD (0001) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | AND (0011) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | STO (1000) | ||
| + | |||
| + | Clock | ||
| + | |||
| + | ===== Builder' | ||
| + | |||
| + | Note the currently manufactured board has a single erata that requires the cutting of one track and soldering of one wire between 2 points. The build files have not been updated. | ||
| + | |||
| + | The build is very simple. Install | ||
| + | |||
| + | Resistors and capacitors | ||
| + | |||
| + | Transistors and IC sockets | ||
| + | |||
| + | LED's | ||
| + | |||
| + | Switches | ||
| + | |||
| + | Undertake the required modification as per the erata photo | ||
| + | |||
| + | ===== Photo Gallery ===== | ||
| + | |||
| + | [[https:// | ||
| + | |||
| + | Bare board | ||
| + | |||
| + | {{[[lib: | ||
| + | |||
| + | Erata Photo - Rear cut and wire jump | ||
| + | |||
| + | {{[[lib: | ||
| + | |||
| + | ===== File List ===== | ||
| + | |||
| + | Filename | ||
| + | |||
| + | Filesize | ||
| + | Last modified | ||
| + | [[https:// | ||
| + | 1.8 MiB | ||
| + | 2019/01/16 20:14 | ||
| + | [[https:// | ||
| + | 1.9 MiB | ||
| + | 2019/01/16 20:14 | ||
| + | [[https:// | ||
| + | 1.9 MiB | ||
| + | 2019/01/16 20:15 | ||
| + | [[https:// | ||
| + | 783.4 KiB | ||
| + | 2019/01/16 20:23 | ||
| + | [[https:// | ||
| + | 123.9 KiB | ||
| + | 2019/01/16 19:54 | ||
| + | [[https:// | ||
| + | 74.9 KiB | ||
| + | 2019/01/16 19:41 | ||
| + | [[https:// | ||
| + | 181.2 KiB | ||
| + | 2019/01/16 19:46 | ||
| + | [[https:// | ||
| + | 8.0 KiB | ||
| + | 2019/01/16 20:36 | ||
